รายละเอียดสินค้า |
Features:
- Stereo Wattage: 3000W @ 2 ohms, 2100W @ 4 ohms, 1200W @ 8 ohms
- Bridged Mono Wattage: 4200W @ 8 ohms, 6000W @ 4 ohms
- Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
- Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
- 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
- New system monitoring provides software visibility of AC line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and power cord
- Updated HiQnet Band Manager and System Architect control software
Specifications
Output Power |
3000W @ 2 Ohms Stereo (per Channel)
2100W @ 4 Ohms Stereo (per Channel)
1200W @ 8 Ohms Stereo (per Channel)
6000W @ 4 Ohms Bridged-Mono
4200W @ 8 Ohms Bridged-Mono
|
Damping Factor |
20Hz to 1kHz > 500 |
Input Sensitivity |
1.4Vrms |
Input Impedance |
20k Ohms (Balanced)
10 kOhms (Unbalanced)
|
Gain |
32.9dB @ 1kHz, 8 Ohm Rated Output |
Frequency Response |
(at 1 watt, 20Hz – 20kHz) +0dB, -1dB |
Signal-to-Noise Ratio |
XTi1002/2002/4002: 100dB (A weighted)
XTi6002: 103dB (A weighted)
|
Total Harmonic Distortion (THD) |
< 0.5% |
Connections |
Input Connectors: XLR, one per channel
Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
HiQnet USB Connector: Type B, connects to HiQnet network.
|
Controls Front Panel |
Level: Two front-panel rotary level controls, one for each channel
Power Switch: On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen: Backlit liquid crystal display that shows preset and processing status
|
Indicators |
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
-10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.-20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
|
Cooling |
Proportional speed fan with front-to-rear airflow. |
Power Consumption |
15.3A; no more than 180W at idle |
Power Requirements |
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz |
Dimensions |
19 x 3.5 x 16.2″ (48.26 x 8.89 x 41.14cm) |
Weight |
24.0 lbs (10.9kg) |
Specialties |
DSP Includes EQ, Crossover Filters, Delay, and Subharmonic Synthesizer
Protection for Short Circuits, Overloads, and Overheating
|
|